How to Re-wire a Potted Motor, Part 5: Covering Wire Joints with Heat Shrink Tubing

Now that we’re able to solder two wires together, we’ll use heat shrink tubing to cover the soldered joints. It’s quick and easy.

Heat shrink tubing is just a little tube of thin, rubber-like material. You cut it to length with scissors. Then you slide it over your wire joint, apply heat with a cigarette lighter or heat gun and it shrinks a predetermined amount, acting as insulation and protection. It comes in different sizes and many different materials, but there's a particular kind we need.

How to Re-wire a Potted Motor, Part 4: How to Terminate Your Wires

If you are able to solder as shown in Part 3, congratulations! That’s the most difficult part to learn. These next few things are much simpler in comparison.

Once we finally replace our old motor leads with new wiring, we’ll need to connect the ends of that new wiring to the “3-Pin Terminal Body,” which is this thing:

When we detach it later, you’ll see that inside are three threaded brass studs:

The wires need to connect to these studs. We’ll eventually connect them by either a) crimping pre-bought ring terminals onto them, or b) creating ring connections on the ends of the wires ourselves. I’m going to show you both methods so you can decide which you prefer.

How to Re-wire a Potted Motor, Part 3: Learning to Solder

Once you’ve mastered wire stripping and braiding (as shown in Part 1) and understand the tools you’ll need (explained in Part 2), we can get down to actual soldering practice.

First thing I’ll say is, a soldering iron is dangerous. So is a kitchen stove and a steak knife. Because we learn early on to use a stove and a knife with care, we can use them daily without having any accidents. That same care should be taken with a soldering iron. Here are some steps I recommend:

A. Clean up your workspace. The soldering iron needs a dedicated place to rest where nothing else is near it. The tip gets extremely hot and there should be no chance it will accidentally touch anything, either while it is at rest or while you are using it. Remove all obstructions from your work area, leaving only the things you will need to do the job.

How to Re-wire a Potted Motor, Part 2: Tools/Materials Required for Soldering

You only need the one in the middle

If you can learn to solder, you can breathe new life into that basket-case 15-91 or 201-2 you’ve got with the rotted wiring insulation. If you’ve mastered the wire braiding we went over in Part 1, now you’re ready to try soldering. But before we get to that, I’ll describe the proper tools required, because I don’t want you to overeagerly buy the wrong items first like I did. Read this before you spend any money.

Also consider this: The soldering process requires holding the tip of a soldering iron against your wire joint to heat it, then adding solder. It requires a fairly steady hand--you may have to hold the iron steady for 30 seconds or longer with some precision--so if you have grip issues or arthritis, you may find this challenging; please read the “arthritis” paragraph at the bottom.

Tools and materials you’ll need:

How to Re-wire a Potted Motor, Part 1: Wire, Wire Stripping, & Wire Braiding

Singer’s models 15-91 and 201-2 come with beltless, direct-drive motors colloquially called “potted” motors. Sometimes the wiring inside is shot and needs to be replaced; half a century of temperature extremes can rot the insulation away, leaving dangerous bare-metal wires inside an all-metal machine that can transmit a shock to the user.

In this series of entries I’ll teach you to re-wire a potted motor. I’m writing this for people with zero experience, so there are quite a few tools and skills we’ll need to cover. The good news is, you can practice all of these skills without touching your sewing machine, so you can be sure you’ll be able to pull this off before you open your machine up.

Also be aware that you’ll need to acquire a fair amount of tools and materials to re-wire a motor. You or your spouse may already own some. In a nutshell, what we’re ultimately going to need is:

- Wiring
- Wire Strippers/Cutters
- Soldering Iron
- Solder
- “Helping Hands” Tool
- Heat Shrink Insulation
- Heat Gun or cigarette lighter

In addition, you may also need a crimping tool and ring connectors; you'll decide for yourself after we cover how to terminate the wire in a future entry. And don’t worry if you don’t know what some of this stuff is, we’ll eventually get into all of it.

More Updates Soon, and Send Me Craigslist Photos to ID!

Have you gotten any better at ID’ing Singers from Craigslist photos? I hope so, as it can really pay off. Case in point: I’m selling a 201 to an acquaintance, and she needs a table for it. I started cruising Craigslist looking for cheap sewing machine tables/cabinets to buy, and came across this one for $30 (cheap for the NYC area):

I immediately recognized it as a 206, Singer’s first zigzag. At 30 bucks I couldn’t pass it up, so I went the next day and fetched the machine. Not a bad deal; I've got a table for my buyer and scooped up a great machine in the process. 

So how could I tell it was a 206?
 

The giveaways that this was a 206

Model 206s are not easy to come by, and the ad was a week old by the time I stumbled on it. If the person had put “Singer 206” at the top of their ad, I’m sure the machine would’ve been long gone. 

If you need help ID’ing a Singer from a crappy photo, e-mail me a photo or a link to the ad, and I’ll identify it for you if I can. (I’ll post those photos and explanations here, but don't worry, I won't post the link to the ad if you're worried about competition from other buyers.) You can e-mail me at:

vintage (dot) singers (dot) nyc (at) gmail (dot) com 

Due to popular demand, I’ve been working on tutorials for how to re-wire a potted motor, like you’d find on a model 15-91 and a 201-2. Because I’m writing it up “… For Dummies” style, it is going to be long. I am aiming this tutorial at people who have zero electrical experience, so there’s quite a lot of information and tips I need to convey, and even reviews of different tools you can do the job with. Please be patient and I'll starting posting the multi-part series soon. 

In the meantime, feel free to send those Craigslist photos if you need help.

Bad Wiring? Save the Terminal Plug Before You Trash It

As every vintage sewing machine hunter knows, a lot of times you buy a machine and the seller insists you take the cabinet it's mounted in, because they just want it out of their garage. The first few times that's fun--hey, free desk!--but soon you have more cabinets than you know what to do with.

If you have a Singer that's been wired for cabinet use, it will have a "single lead" power cable with just one set of wires going into the terminal plug. Here's the one from my latest acquisition:

As you can see, this one's in poor shape and needs to be tossed. The wiring insulation looks like it dates to the Eisenhower administration and you can see bare metal. But before we get rid of it, we're going to "harvest" the Singer terminal plug, so that later we can easily--and inexpensively--make ourselves a new power cable.

Restoring a 201-2: Interview with Elle Dubya of "My Sewing Machine Addiction"

Elle Dubya's restoration projects: One down, one to go

A month before I started this blog, California-based homemaker "Elle Dubya" fired up a vintage Singer blog of her own. Titled "My Sewing Machine Addiction," it chronicles her impressive mission of completely tearing down and rebuilding a model 201-2 that she acquired in May. Her blog went up in June, and I've been hooked ever since discovering it. "When I purchased this 201-2, I rushed into buying her," Elle admits, and it's a feeling many of us know well. "I was charmed by her decals, and it wasn't until I got home and into good light that I realized that she was in really bad shape."

The 201-2's condition earned it a nickname: "I named her Ms. Rusty," Elle says. "I couldn't move the needle, her gears were locked up, and she was in dire need of both aesthetic and functional repair.  At that point I figured I couldn't really do any more harm to her so I might as well try fixing her up...even though I was probably diving into the deep end of the pool."

Elle's 201-2 rescue project is fascinating and inspiring because 1) She's tearing down everything on the machine, and 2) she's never done this before. Although her grandmother taught her to sew at a young age, the 40-something Elle didn't get back into sewing until her thirties, and "the vintage sewing machine bug bit me just this year," she confesses. How did that happen? Read on for the Vintage Singer Sewing Machine Blog's first People Profile, the Elle Dubya interview!

VSSMB: You got into vintage sewing machines just this year. What's the story?
Elle Dubya: I was looking to get a Featherweight because they are such cute little machines and are easy to transport to quilting class.  Unfortunately, I'm also a cheapskate, or "bargain shopper" depending on your view… 

A Visual Guide to Identifying Singers from Crappy Craigslist Photos, Part 5: Is It a 99?

Model 99, up top, is stubbier. Model 66, on the bottom, is longer.

The model 66 is a full-size machine; the model 99 is a 3/4-size machine with the same visual DNA as the 66, the same lines and curves. Identifying the model 99 by sight is fairly easy, because it's just a horizontally-squashed version of the model 66, as you can see above.

The model 99 is the only 3/4-size machine I'm covering in this series. One other 3/4-size machine you might see on Craigslist--I've only seen one once or twice--is the model 28/128. This is easily distinguishable by the shovel-shaped inspection plate and/or dual slide plates:

NOT a 99, as evidenced by these features.

So, if you see either of those indicators, you'll know it's not a 99. The 99 has a single center-mounted slide plate, as seen below:

A Visual Guide to Identifying Singers from Crappy Craigslist Photos, Part 4: Ruling Out the 27/127, Ruling In the Model 66

Now that we've learned to figure out if a tiny Craigslist photo is of a Singer 15 or 201, we'll next turn to the model 66. The 66 was the entry-level Singer and is extremely common on my local (NYC-area) Craigslist.

The model 66's silhouette can easily be mistaken for a model 27 or 127, so the first thing we'll learn to do is rule that out. The model 27/127 has two dead giveaways that are easy to spot from many angles: 1) A silver shovel-shaped inspection plate, and 2) Dual slide plates running the entire width of the bed:

NOT a 66, as evidenced by these features.

So if you spot either of these items in any given photo, you can be sure it's not a 66. And either of those features are often visible in even the smallest, darkest photo.

Next, how do we determine if it IS a 66? If you're dealing with a large photo, the 66 has some unique lines. The top and bottom lines of the arm are both slightly curved and tapered inward, and there's that Ski Jump area that's too steep to be a model 15:

But what if you're dealing with a tiny, dark photo? When the photo is not clear or shot at a bad angle, the 66's lines can often be mistaken for both the 15 and the 201. In that case we need to rely on some other clues.